Showing posts with label Ring. Show all posts
Showing posts with label Ring. Show all posts

Thursday, 7 July 2022

Crikey Not Christmas 2022 Part 13

 Crikey Not Christmas 2022 Part 13

A nice quick blog this week.

Pair of Pine Cones











I wanted to make the Wreath more 3 Dimensional. I know that sounds weird as it already was but simply being a Ring it looked too flat.

Therefore I decided to add some Pine Cones. I wanted them a similar size so began comparing them. I wanted 3 in total.

Trying to Glue

 










Once selected I took a Pine Cone and tried to Glue it in place using my usual Glue. It didn’t go well. The Pine Cones Shape meant that there was little surface to place the Glue.

Trying to Sew

 










To try and give it some extra Strength I tried to part Sew the Cone to the Ring. This was done by securing the Thread to the Ring. Then winding the Thread in and out of the Pine Cone. Needless to say all that happened was tangled mess.

Superglue to the Rescue


 









Luckily I had some Superglue in my Craft Stock. I used that to Glue the Pine Cones in place. This was done at roughly equal placing. See above photograph.


Thursday, 12 May 2022

Crikey Not Christmas 2022 Part 5

 Crikey Not Christmas 2022 Part 5

Okay I think I have found a Solution.

Scrap Green








 

In order to get around this particular problem I am going to Cut the Ribbed Material into 2 pieces. I am then going to fill the middle with Scraps.

Once the Scraps are Dry I shall place the 2 good pieces of Ribbed Wool at Either End. Hopefully this should make the whole thing look like it is an uninterrupted flow.

Cover Back


 









Having finished with the Front I turn my attention to the Back. With the adjustments I have had to make I am going to have to add more Scraps. This will be to the Back and Inner Ring.

Front Completed










 

The Front has come out well. Unfortunately it isn’t just this part that will be seen when Hung.

Wind Tight









 

I have found some Green Wool to Wind Tight around the Ring. Not only does this help keep all the Straggly bits in place but also gives a nice Decoration

It has also given me an idea.

Thursday, 21 April 2022

Crikey Not Christmas 2022 Part 2

 Crikey Not Christmas 2022 Part 2

Did you work it out? I am going to make a Christmas Wreath.

White Strips

 







After sorting through my Hoard I decided on using White Strips of Material. Most of these are Offcuts from Pattern. Since quite a few have writing on they aren’t much use for other things.

Smaller White Strips

 









Now I have my Material I need to Cut it into Finer Smaller White Strips. Otherwise it is going to make the Process bulky and difficult to do.

Begin Wrap









 

Taking the Largest of the Three Rings I begin to Wrap. I am not bothering with using special Fabric Glue at this point. I Wrap all the way around at a slight Angle.

First Layer Complete

 










Here is the First Complete Layer. When I say Complete Layer I am not referring to once around the Ring. As you can see in the above photograph it has grown quite a bit in Girth.

This took several times around the Ring with gradually using Thicker Strips of Material. It is quite Time Consuming as you have to wait for the Glue to Dry. Therefore Layer in this case refers to the Finish of one Selection of Material


Thursday, 15 June 2017

Sewn Head Scarf 2017 Part 1

Sewn Head Scarf 2017 Part 1

I have a problem with the sun especially in summer. Therefore I always need to have some kind of head covering to protect me. This could either be a hat or some kind of scarf.

Since I am a little short on summer headwear I have decided to use up some cloth I have to make a Headscarf

Square Piece of Cloth














The cloth I have is calico and I cut out a rough square. I did not measure it I just did it by eye.

Cloth Hemmed














Next I did a rough hem all around with a tacking stitch with beige cotton thread. The size worked out at about 16 Inches square.

Ribbon Attached








After hemming I sorted out some ribbons. I decided on green and proceeded fold over and sew both the ends to prevent fraying. I then attached one ribbon at the top right hand corner and one at the bottom left hand corner.

Once these two ribbons were added I then folded the rough hem over to make a new hem. This time I used a running back stitch. To make it more decorative I used a twin dark green thread on two sides of the square and a light green on the other two sides.

Fleur de Lys Template Middle 







The next step was to decide on a design. I am rather partial to the Fleur de Lys. I therefore drew a Fleur de Lys Template on a spare bit of cardboard. I then cut out the Template.

Folding the square into a triangle with the ribbons both at the end I found the middle. I then placed the Template on the cloth and drew around it in pencil.

Fleur de Lys Template Bottom









After drawing the first Fleur de Lys I turned the cloth over downwards. On the opposite side I drew another Fleur de Lys. This time I positioned the Template at the bottom of the cloth.

Both Fleur de Lys Templates
















The above photo shows both of the Designs drawn with the fine detail added.

Drawn Design in Ring













In order to make embroidering easier I put the cloth into a wooden ring to hold it taut. 

Light Green Outlined Fleur de Lys
















Taking two threads of Light Green Embroidery Silk I backstitched the outline. I then embroidered the band in a darker green.

Both Fleur de Lys Outlined
















After the first one was outlined I then repeated the process with the other design only this time I reversed the colours. As of yet I haven’t decided about the filling in of the designs.I will let you know in the next blog.