Showing posts with label Layer. Show all posts
Showing posts with label Layer. Show all posts

Thursday, 21 April 2022

Crikey Not Christmas 2022 Part 2

 Crikey Not Christmas 2022 Part 2

Did you work it out? I am going to make a Christmas Wreath.

White Strips

 







After sorting through my Hoard I decided on using White Strips of Material. Most of these are Offcuts from Pattern. Since quite a few have writing on they aren’t much use for other things.

Smaller White Strips

 









Now I have my Material I need to Cut it into Finer Smaller White Strips. Otherwise it is going to make the Process bulky and difficult to do.

Begin Wrap









 

Taking the Largest of the Three Rings I begin to Wrap. I am not bothering with using special Fabric Glue at this point. I Wrap all the way around at a slight Angle.

First Layer Complete

 










Here is the First Complete Layer. When I say Complete Layer I am not referring to once around the Ring. As you can see in the above photograph it has grown quite a bit in Girth.

This took several times around the Ring with gradually using Thicker Strips of Material. It is quite Time Consuming as you have to wait for the Glue to Dry. Therefore Layer in this case refers to the Finish of one Selection of Material


Thursday, 23 September 2021

All Steam Ahead 2021 – Mad Hatter Preparations Part 3

 All Steam Ahead 2021 – Mad Hatter Preparations Part 3

This is a nice quick blog. Adding Cogs.

Add Cut out Cogs

 









I started to Glue the Cut out Cogs to the Hat. I had made quite a few of them now and of different Sizes. For some reason the Base Covering had left a lot of Glue Residue. I wanted to Cover as much of this as possible.

Add Cogs other Side

 









Once I had added a Bottom Layer of Cogs one Side I turned the Hat around and carried on adding.

Add Metal Centre

 










The Black Cog Shapes were only the Silhouette. To give them a proper Cog look I Glued a Metal Washer to the Centre of Each Cog Shape.

Front Right









 

After doing the Bottom Layer I started to fill in the Gaps with more Cogs. 

Front Left









 

When I was satisfied with one Side I moved on to the other. 

Top Cogs




I had used up all the Cogs I had made so I had to make some more before I could add to the Top. I also had to add a few more to the Back of the Hat.

Thursday, 12 August 2021

Pyramid Power 2021 Part 2

 Pyramid Power 2021 Part 2

I was finding Cutting these Matchsticks very Time Consuming.

Clever Clippers

 






I remembered a Tip whilst I had been doing some Researching on the Internet. One suggest was to Clip Matchsticks with a pair of Nail Clippers.

Due to lack of Instructions I had decided what I was calling the Base would actually be the final Top part of the overall Pyramid. I would have to work out how to do the Hollow part later.

First Layer










I found using the Nail Clippers made things a little better and was soon ready to add my First Layer to the Base. In order to strengthen it I decided to put the Matchsticks the Opposite Direction.

It wasn’t just the Length of the Matchsticks that had been giving me problems. If you look at the above photograph you can see that many of them were Warped. This meant they didn’t lay snuggly together.

Two Short Planks

 










After the First Layer was dry I began to Add the Second. However this Time I was one Matchstick Minus at either End.

Pyramid Steps

 








I continued to Add a Layer at a time. Each Layer was 2 Matchsticks Fewer than the Previous Layer. Not only that I was Clipping the Matchsticks I was Adding Shorter each time.

 

Poly Cement



I was finding the Sticking very hard work. Half the time the Matchsticks were coming off again in my hand. Not only that the whole thing seemed extremely Brittle.

Since this part of the Pyramid was going to be the Top I was going to need something far better than the PVC Glue I had been using for the Main Structure. I decided to seek professional advice from Heaps our local Art shop. He recommended Poly Cement.