Showing posts with label Strips. Show all posts
Showing posts with label Strips. Show all posts

Thursday, 15 May 2025

Crawling Creatures 2025 Part 8

Crawling Creatures 2025 Part 8

Even with both the Crab and Starfish finished I still have quite a bit of Clay left. Hm playtime I think.

Large Black Ball









I have lots of Black and White Clay left. Therefore I started with a Large Black Ball

Flattened Black











I Flattened the Ball with my Palm to make a Base.

Pull Tail










I tease some of the Black Clay out at the Bottom to make a Tail.

Knife Spiral










Taking a Knife I make a Rough Spiral in the Clay.

White Strip







Next I take some White Clay and make a Thin Strip.

Fill Spiral











I slowly begin to Fill the Spiral. It takes a couple of Strips to do this.

Thursday, 21 April 2022

Crikey Not Christmas 2022 Part 2

 Crikey Not Christmas 2022 Part 2

Did you work it out? I am going to make a Christmas Wreath.

White Strips

 







After sorting through my Hoard I decided on using White Strips of Material. Most of these are Offcuts from Pattern. Since quite a few have writing on they aren’t much use for other things.

Smaller White Strips

 









Now I have my Material I need to Cut it into Finer Smaller White Strips. Otherwise it is going to make the Process bulky and difficult to do.

Begin Wrap









 

Taking the Largest of the Three Rings I begin to Wrap. I am not bothering with using special Fabric Glue at this point. I Wrap all the way around at a slight Angle.

First Layer Complete

 










Here is the First Complete Layer. When I say Complete Layer I am not referring to once around the Ring. As you can see in the above photograph it has grown quite a bit in Girth.

This took several times around the Ring with gradually using Thicker Strips of Material. It is quite Time Consuming as you have to wait for the Glue to Dry. Therefore Layer in this case refers to the Finish of one Selection of Material


Thursday, 10 January 2019

Owl say that’s an unusual Yule Gift 2018/19 – Part 2


Owl say that’s an unusual Yule Gift 2018/19 – Part 2

If you haven’t guessed what I am making yet maybe the next few pictures will give you a clue.

Foam Circle Cut Out







  
I take some Foam approximately a thumb joint thick. I draw two Circles and cut them out.

Stick Foam Pad
 










If you look carefully at the above photograph you should be able to see one of the Inner Circles that I drew.

This is because before sticking the Pad down I have shaped it slightly. I do not want the Foam to be flat. I want it to be slightly Dome Shaped

I made the Dome Shape a little piece at a time as I didn’t want the curve to be too sharp.

Tie Dry











Once I had finally got the shape I wanted then stuck a Foam Pad to each piece of Owl material. I have tied the Strips around it whilst it dries.

Purple Material








I have cut out two circles of Purple Material which I place over the Dome I then stick them to the Foam. Since the item is Circular the material needs to be folded over slightly.

Underside of Pads Part Sewn








In the photo above you can see that the material is folded over at an angle following the curvature of the Foam. The Pad on the right is not quite dry yet.

Tools of the Trade










One thing you have to be sure of is to use the right tools when crafting. I am trying to sew through both Foam and PVC material and in consequence have broken two of my needles.

Fortunately I possess quite a few. I have changed to my leather work needles to work with.

Owl Material Drawn










I sew around the material with my leather-work thread and then I pull it tighter. It now reminds me a little bit of a shower cap.

Velcro
 






When I had finished with the Pads I turned my attention to the Strips around it. I trimmed and hemmed the ends of the Strips then proceeded to add Velcro to them.

I stuck the Velcro on with glue then I waited for it to dry. Next I sewed around the edges of the Velcro to make sure they were secure.

Velcro Wrapped









Since these Strips are going to be Straps I had to make sure that I put the Velcro on the right way. Therefore I did one strap at a time.

I found that one part of the Velcro had to be on Top of the Strip and the other half had to be on the Bottom.

The above photograph shows this better than describing it. The left one is just stuck together. The right one is wrapped up to be tidy.

There you have it a pair of customised Owl Knee Pads.